Sherwood RVD-9090R Guía para resolver problemas

POWERON/OFFSPEAKERPHONESCH SELECTOR CHANNEL LEVEL TUNING/PRESET MODEBASS TREBLEMASTER VOLUMEINPUT SELECTORVCR 2 INPUTVIDEOS-VIDEOL AUDIO RSTANDBYSTAND

DIGI LINK III System Remote Controls10POWER1 2 3 4 56 7 8 9 0OSD ENTERCDCDABTUNERDISCREPEATDECK SEL.INTROSCANAUXDVD/TVVCR1EQPRESETVCR2TAPE MON.6CH DIR

11OPTICAL 1 OPTICAL 2 COAXIAL 1 COAXIAL 2BAND FM MODE MEMO/ENTERDYNAMIC RANGE CINEMA EQ SPEAKER MODERDIRECTDTSDIGITALPOWERON/OFFSPEAKERPHONESCH SELECT

Adjusting the speaker settingsENGLISH12With the receiver in any of thesurround modes, press theSPEAKER MODE button formore than 2 seconds to enterthe

13Engage the Test Tone mode by pressingthe Test Tone button on the remotecontrol.9󳀏In these modes, the volume level of each channelcan be adjusted usi

14In the Dolby Digital mode, repeat theabove steps 13 and 14 to adjust the reardelay time.15Adjusting delay times of thespeakers in Dolby Digital(AC-3

15LISTENING TO A PROGRAM SOURCEBefore operationSelect the desired input source.3󳀏Enter the standby mode.󳀏The STANDBY indicator lights up.The receiver

ENGLISH16Operate the selected component forplayback.5 Notes:󳀏 Extreme settings at high volume may damageyour speakers.󳀏 In the DTS or Dolby Digital (A

17To compensate for edgy or shrill moviesound tracks.9To listen with headphones.11󳀏Press it again to cancel.󳀏“MUTE” will flicker.󳀏To resume the previo

ENGLISHDTS (Digital Theater System) : Allows you to enjoy 5.1(or 6) discrete channels of high quality digital audiofrom DTS program sources bearing th

19ENJOYING SURROUND SOUNDSelect the desired surround mode.󳂮When selecting the DTS or Dolby Surround mode.󳀏When playing program sources bearing the “

2IntroductionCongratulations on Your Purchase!Your new high fidelity receiver is designed to deliver maximum enjoyment and years of trouble free servi

20LISTENING TO RADIO BROADCASTSPresetting radio stationsAuto tuning󳀏Each time this button is pressed, the mode changesas follows;󳂵 Tuning mode : “PRES

21Repeat the above steps 1 to 3 to memorizeother stations.4After selecting the tuner as input source,select the preset tuning mode.1Listening to FM st

22RECORDINGStart recording on the component connectedto the TAPE MONITOR.2Select the desired input as recording sourceexcept for TAPE MONITOR.1Recordi

23Operating the sleep timer󳀏The sleep timer allows the system to continue tooperate for a specified period of time beforeautomatically shutting off.󳀏T

24Using the OSDCURRENT STATUS DISPLAYThis mode shows the status corresponding to each operation.󳀏The on screen display will automatically disappear in

25Select the desired menu using the CURSORUP(▲) or DOWN(▼) button.2CINEMA EQFM MODEorPOWER1 2 3 4 56 7 8 9 0OSD ENTERCDCDABTUNERDISCREPEATDECK SEL.INT

26Select the desired menu or (and) change thecondition with the corresponding buttons. 4Repeat the above steps 2~4 to change theconditions on other me

Troubleshooting Guide27PROBLEM POSSIBLE CAUSE REMEDYNo powerNo soundNo sound from the rearspeakersNo sound from the centerspeakerStations cannot be re

28󳂮 AMPLIFIER SECTION󳀏Power output, stereo mode, 8 Ω, THD 0.2%, 40 Hz~20 kHz ...

RVD-9090RAUDIO/VIDEO RECEIVEROPERATINGINSTRUCTIONS5707-04712-001-0

FOR U.S.A. AND CANADA ...120 VUnits shipped to the U.S.A. and Canada are designedfor operation on 120 V AC only.Observe a

4CONTENTSIntroduction󳀏UNPACKING AND INSTALLATION ...

5System ConnectionsANTENNADIGI-LINKAC INPUT120V~60HzSWITCHED120V~60Hz100W 1A MAXAC OUTLETMODEL NO. RVD-9090RAUDIO/VIDEO RECEIVERThis device complies w

6ANTENNADIGI-LINKAC INPUT120V~60HzSWITCHED120V~60Hz100W 1A MAXAC OUTLETMODEL NO. RVD-9090RAUDIO/VIDEO RECEIVERThis device complies with Part 15 of the

ANTENNADIGI-LINKAC INPUT120V~60HzSWITCHED120V~60Hz100W 1A MAXAC OUTLETMODEL NO. RVD-9090RAUDIO/VIDEO RECEIVERThis device complies with Part 15 of the

8Front Panel ControlsINPUT, FREQUENCY, VOLUME LEVEL, OPERATING INFORMATIONS, etc.STEREO INDICATORTUNED INDICATORAUTO INDICATORDOLBY( ) PRO LOGIC I

9Speaker PlacementTo obtain the best surround sound effect in your home, place the speakers asfollows;󳀏Front speakers: Place each front speaker about